Here are the plans for a workbench for your business must be given. Fairly easy to build, these plans is a nice, firm experience in a compact bench in almost all the workshops.

Items needed:

Top 198 x 48 x 1800 millimeters
Corner 90 x 35 x 240 mm
Top side rails 148 x 48 x 800mm
Front / rear top rail 90 x 35 x 1400mm
Anchor bolts, nuts and washers 5 / 16 x 4 ½
Bottom side rails 90 x 35 x 800mm
Legs 98 x 98 x 900mm
Front / rear floor joists 90 x 35 x 1400mm
Shelf800 x 1470 x 19mm
Bench Stop 90 x 35 x 300mm

Tools

Claw Hammer
Smoothing
Marking gauge
Combination Square
Steel strip
Three beveled edge chisels
Chop saw
Tenon saw
Nail Punch
Twist Drill
Screwdrivers
Olive Stone
Sanding cork
Variable speed drill
Jigsaw
Circular Saw

Instructions:

1. Cut down on all fours, and Mark in quarters for the length of the upper and lowerRails. The upper frame is 148 millimeters x 48 millimeters in depth, the lowest 90 millimeters x 35 millimeters in depth. Set your circular saw to the depth on the right side and cut waste lines you marked. Cut a series of parallel lines on 12 mm spacing between the marks of accommodation and knock out the waste. Smooth each case with a chisel and rasp.

2. Cut to length front and rear of the upper and lower rails together in their house and pin in place with nails. Drill through both legs and rails, as shown and bolt rails to the legs.Check frame is square by measuring diagonals.

3. Cutting pliers and side rails of the chassis front and rear, drilling, and then insert the screws longer. Tighten all nuts and not seek the rock table.

4. Cut four brackets at the corner angle of 45 degrees. A miter saw will be useful for this or a circular saw about 45 degrees. Screw brackets, instead of flush with the upper guide. At this stage, within the Bank should be in a completely rigid.

5. Cutmatch the dimensions of the bottom shelf of the bank. 35mm x 133mm clear notch in every corner of the legs. The shelf can be screwed in place or lose.

6. Cut five pieces for the top. They move on to obtain a good fit for the borders and keep them in place with a nail. Screw on the bench frame with 100 mm screws, two at each end, just sunk below the surface. Use a level of smooth, non-serious irregularities.

7. Preparing to stop a bank, as explained in detail. FindEast and measures 60 millimeters and 200 millimeters from one end of a length of 90mm x 35mm pine. Drill a hole diameter of 8 mm in these points. Draw two lines, holes and cut along the lines with a jigsaw puzzle to form a crack. Facilitating the cut with a file or a strong chisel. End Bevel to 45 degrees. Cut Bank to a length of 300 millimeters.

8. Locate the bank stop wherever you want. Generally favor the right hand stop on the left side of the counter and handed the contrary. Be sure to avoid that, evenparentheses. Keep a stop at the bank's front rails and Mark around it on the underside of the bench top. Transfer form for the top of the bank.

Drill two holes in opposite corners and cut a rectangular hole. Set to stop the bank and ensure that glides smoothly. Personalize with a file or a chisel if necessary. Press to stop the bank, so it is flush with the top bench and drill a hole through the railing at the top of the slot. Insert a carriage bolt with a washer and wing nutTo enable the Bank to be brought to stop and a bit 'low.

On average, work benches are not complete, ie do not apply paint or a clear surface, so that this does not mark the end of other objects, which are built on the bench.

See Also : Power Tools Backpack Blower Review